|
Simple Guidelines
A charger designed to service NiMH batteries
can also accommodate NiCd’s, but not the other way around.
A charger only made for the NiCd batteries could overcharge
the NiMH battery.
While many charge methods exist for nickel-based
batteries, chargers for lithium-based batteries are more defined
in terms of charge method and charge time. This is, in part,
due to the tight charge regime and voltage requirements demanded
by these batteries. There is only one way to charge Li-ion/Polymer
batteries and the so-called ‘miracle chargers’,
which claim to restore and prolong battery life, do not exist
for these chemistries. Neither does a super-fast charging
solution apply.
The pulse charge method for Li-ion has
no major advantages and the voltage peaks wreak havoc with
the voltage limiting circuits. While charge times can be reduced,
some manufacturers suggest that pulse charging may shorten
the cycle life of Li-ion batteries.
Fast charge methods do not significantly decrease
the charge time. A charge rate over 1C should be avoided because
such high current can induce lithium plating. With most packs,
a charge above 1C is not possible. The protection circuit
limits the amount of current the battery can accept. The lithium-based
battery has a slow metabolism and must take its time to absorb
the energy.
Lead acid chargers serve industrial markets such
as hospitals and health care units. Charge times are very
long and cannot be shortened. Most lead acid chargers charge
the battery in 14 hours. Because of its low energy density,
this battery type is not used for small portable devices.
In the following sections various charging needs
and charging methods are studied. The charging techniques
of different chargers are examined to determine why some perform
better than others. Since fast charging rather than slow charging
is the norm today, we look at well-designed, closed loop systems,
which communicate with the battery and terminate the fast
charge when certain responses from the battery are received.
Battery manufacturers recommend that new batteries
be slow-charged for 24 hours before use. A slow charge
helps to bring the cells within a battery pack to an equal
charge level because each cell self-discharges to different
capacity levels. During long storage, the electrolyte tends
to gravitate to the bottom of the cell. The initial trickle
charge helps redistribute the electrolyte to remedy dry spots
on the separator that may have developed.
Some battery manufacturers do not fully form
their batteries before shipment. These batteries reach their
full potential only after the customer has primed them through
several charge/discharge cycles, either with a battery analyzer
or through normal use. In many cases, 50 to 100 discharge/charge
cycles are needed to fully form a nickel-based battery. Quality
cells, such as those made by Sanyo and Panasonic, are known
to perform to full specification after as few as 5 to
7 discharge/charge cycles. Early readings may be inconsistent,
but the capacity levels become very steady once fully primed.
A slight capacity peak is observed between 100 and 300 cycles.
Most rechargeable cells are equipped with a safety
vent to release excess pressure if incorrectly charged. The
safety vent on a NiCd cell opens at 1034 to 1379 kPa
(150 to 200 psi). In comparison, the pressure of
a car tire is typically 240 kPa (35 psi). With a
resealable vent, no damage occurs on venting but some electrolyte
is lost and the seal may leak afterwards. When this happens,
a white powder will accumulate over time at the vent opening.
 Commercial fast-chargers are often not designed in the
best interests of the battery. This is especially true of
NiCd chargers that measure the battery’s charge state
solely through temperature sensing. Although simple and inexpensive
in design, charge termination by temperature sensing is not
accurate. The thermistors used commonly exhibit broad tolerances;
their positioning with respect to the cells are not consistent.
Ambient temperatures and exposure to the sun while charging
also affect the accuracy of full-charge detection. To prevent
the risk of premature cut-off and assure full charge under
most conditions, charger manufacturers use 50°C (122°F) as
the recommended temperature cut-off. Although a prolonged
temperature above 45°C (113°F) is harmful to the battery,
a brief temperature peak above that level is often unavoidable.
|
